断桥铝门窗设备双头锯的调整需要哪六步？

(1) adjust the position of the compressed cylinder

将铝合金型材放到该铝门窗设备的工作台面上，两锯头的压紧气缸调整至对工件压紧合适的位置，然后固定压紧气缸。

The aluminum alloy section is placed on the work surface of the aluminum door and window equipment, and the pressing cylinder of the two saw head is adjusted to the most suitable position for pressing the workpiece, and then the cylinder is fixed and pressed tightly.

（2）调整锯片进给速度

(2) adjusting feed speed of saw blade;

先以切割锯出厂的默认锯片进给速度试机，在试机过程中，如果觉得锯片的进给速度不合适时，可以调节工进气缸调速接头，增大或减少进给速度，就可得到所需要的进给速度。

The first factory default to cutting saw blade feeding speed test machine, the test machine in the process, if the feed speed of the saw blade is not right, can adjust the feeding speed of cylinder joints, increase or decrease the feed speed, feed speed will be needed.

 

（3）调整锯削角度

(3) adjust sawing angle;

铝合金型材精密切割锯按上述各项调整完毕，检查符合规定后试运转30分钟。

Aluminum alloy profiles, precision cutting saw, according to the above adjustment, inspection compliance with the provisions of the trial operation 30 minutes.

（4）调整设备90°角的切割（锯片伸出与工作台面垂直）。

(4) adjust the cutting of equipment at 90 degree angle (saw blade extends vertically to the work surface).

铝合金型材精密切割锯出厂前均经调试并经检验合格，在此可直接锯切一铝合金型，材检验其90度角的锯切面是否符合要求，误差为±10′。如若不符合要求，可调整限位挡块上的螺栓。然后再重复锯切测量，使之满足要求。注意要锁紧切割锯上的螺母。

The precision cutting saw of aluminium alloy profile has been debugged and inspected before leaving the factory. It can be directly cut and cut into an aluminum alloy material to test whether the saw section of the 90 degree angle meets the requirement and the error is + 10'. If the requirement is not met, the bolt on the stop block can be adjusted. Then repeat the cut measurements to meet the requirements. Finally, be careful to lock the nuts on the cutting saw.

（5）调整设备45°角的切割（锯片伸出与工作台面夹角成45°时设定为45°）

(5) adjust the cutting of equipment at 45 degrees angle (when the angle between the saw blade extending out and the working table is 45 degrees, set to 45 degrees)

松开工作台上的锁紧手柄，摆角气缸通气，45度角到位后，锁紧把手。锯切型材后检查是否符合要求（误差为±10′）。如果不符合要求，可调整限位挡块上的限位螺钉，重复锯切、测量，使之满足要求。然后再锁紧螺钉上的螺母，拧紧锁紧手柄。

Loosen the lock handle on the work bench, swing the angle cylinder, ventilate, 45 degrees angle in place, lock the handle. Check the section after cutting to see whether it meets the requirement (the error is + 10 '). If not meet the requirements, you can adjust the limit block on the limit screw, repeated sawing, cutting, measuring, to meet the requirements. Then lock the nut on the screw and tighten the handle tightly.

（6）调整型材切割长度。

(6) adjust the cutting length of the profile.

角度调整完毕后，应调整铝合金型材的切割长度。拉动把手带动右锯头沿圆导轨移动至准确位置（看标尺指针），刻度尺指示长度即铝合金型材短边的长度。切割完成后，如切割后型材的长度与要求长度有偏差，应进行微调，微调时，拧紧刹车可调手炳，转动微调手炳至要求尺寸。

After the angle adjustment is finished, the cutting length of aluminum alloy profile should be adjusted. The pulling handle drives the right saw head to move to the correct position along the circular guide rail (see the ruler pointer), and the graduation ruler indicates the length, that is, the length of the short edge of the aluminum alloy profile. After finishing cutting, such as cutting length and the length of required profile deviation should be fine-tuning, fine-tuning, tighten the brake adjustable handle, rotate the handle to the required size adjustment.

针对以上的内容就是由铝切割设备提供，一如既往的为大家提供服务，大家有什么问题想要咨询可进入网站：http://www.szwmdjx.com/product.html我们会有客服为您提供服务。

According to the above content is made of aluminum cutting equipment is provided, as in the past for us to provide service, you have what problem you want to consult can enter the website: http://www.szwmdjx.com we have customer service to provide the service for you.